I'm starting to get a decent collection of tools! Advice for projects?

[Kenyth]

I got an air compressor this past XMas. With the economy down, the prices on tools at Harbor Freight have been almost a givaway! I've been buying tools like crazy (to my wife's disdain)! I built a small work bench/Pegboard. It turned out fairly well! I have a few jobs to do this spring. Put up a fence, put up a shed, and put up an outdoor doghouse/kennel. I plan to build a lot of the stuff I need to work myself. My next project is making some knockdown sawhorses. I plan on modifying them to accept some 2x4 stretchers to create a knockdown work support. I figure I can just cross a couple notched 2x4's to rip or crosscut sheets if I need to. Then, I'll use OSB hinged in the middle to create the top for a knockdown work table. I also need to create a saw guide for my circular saw. I'm thinking that since I'll be cutting a lot of 4x4 and 2x4 stock for my spring projects, a 10" miter saw might be a good investment. I know that a table saw is the first recommended tool for woodworking, because it can miter as well, but I'm guessing that's more for furniture making than mitering long utility stock for framing and fence making.

Anyway, my question for the fence is, do you recommend putting the 4x4 posts in concrete? It will be meant to hold in a sizable dog. IS it 1/2 bag per post? For the shed, should I just put down some 4x4's on the ground or dig in concrete footers for that as well? Levelling the thing will probably be a pain otherwise?

[badwhale]

Consider using something like this instead of casting the posts right into the ground. This will keep them from rotting & allows for replacement later.

I'd cast footers, but I've been know to overkill every single project I undertake.

If you put the 4x4s right on the ground, make sure they're cedar, or pressure treated. However, ANY wood in direct contact with the ground WILL rot eventually.

Will

[ashauler]

I've put up several fences, and I sink the posts in concrete and use some simple aluminum roof flashing at the very top of the concrete to create an angle finish where the post goes into the concrete so any water will drain away from the post. Its very simple to do and the flashing is inexpensive. The concrete raises about 2-3 inces above ground level so basically all the post is in contact with is the concrete.

As far as the shed goes, the footer would be the best and will also help with any critters that want to make under your shed their new home.

[Diesel Grinch]

My advice.


Sell the tools. Just means more work for you.


Having been putting a addition onto my house I have most things. I've done excavating, pored the footing, block work, framing, duct work, plumping, eclectic, roofing, siding, tiling, wood floors, molding and almost anything.


DG

[CoventryCat86]

Here's my table saw:



Powermatic 1792010K. 5hp, 10" with the 50" Accu-Fence system.

As far as a miter saw, I would highly recommend you spend the extra money on a SLIDING COMPOUND miter saw. You can do so much more with those than a cheapie chop saw. Here's mine:



I'd suggest this one, it's a little nicer and newer. It's 12" whereas mine is only 10"



Oh, another fantastic tool is an ORBITAL "sawzall" (reciprocating saw). I have an older Milwaukee regular Sawzall and I borrowed a friend's Porter Cable orbital reciprocating saw and WOW, what a difference! Here's the one you need. model 6536-21:

I'm a huge fan of Milwaukee brand power tools, it's pretty much the only brand I buy. My 3/8" drill, my 1/2" D-handle drill, my palm sander, rotary hammer drill, Sawzall are all Milwaukee brand tools. I will admit though that I have a Porter Cable power planer (door hanging kit), a Porter Cable 3/8" right angle drill, a Freud biscuit jointer, a Skil worm drive circular saw (model 77 I think?) and a Ryobi palm sander (which is a piece of $hit) and a couple of Craftsman sanders (which also suck). My cheapie router is a Porter Cable, it's "okay" it does the job.

[chefchris]

Hey, Bill, why don't you post up a tutorial on how to make a cigar box lamp so Kenyth can break in his new tools?!

[CoventryCat86]

Hey, Bill, why don't you post up a tutorial on how to make a cigar box lamp so Kenyth can break in his new tools?!

1. Post over on CP that you're looking for some free cigar boxes and you'll send "demon sticks" in return then never send your end of the deal.

2. Once you've successfully scammed some cigar boxes from your BOTLs, buy some quartz movement in bulk here from KlockKit. The most you'll ever have to pay is about $3.00 each.

3. Drill a hole in the middle of your cigar box and install the movement. The self adhesive numbers are optional but they look tacky.

4. Start a thread on your favorite cigar site called "Cigar box clocks for sale, $40.00" and see what happens. On sites that protect scammers and thieves, you'll have no problem. You COULD try that here or on CP but you'd have your a$$ handed to you.

[Kenyth]

Here's my table saw:



Powermatic 1792010K. 5hp, 10" with the 50" Accu-Fence system.

As far as a miter saw, I would highly recommend you spend the extra money on a SLIDING COMPOUND miter saw. You can do so much more with those than a cheapie chop saw. Here's mine:



I'd suggest this one, it's a little nicer and newer. It's 12" whereas mine is only 10"



Oh, another fantastic tool is an ORBITAL "sawzall" (reciprocating saw). I have an older Milwaukee regular Sawzall and I borrowed a friend's Porter Cable orbital reciprocating saw and WOW, what a difference! Here's the one you need. model 6536-21:

I'm a huge fan of Milwaukee brand power tools, it's pretty much the only brand I buy. My 3/8" drill, my 1/2" D-handle drill, my palm sander, rotary hammer drill, Sawzall are all Milwaukee brand tools. I will admit though that I have a Porter Cable power planer (door hanging kit), a Porter Cable 3/8" right angle drill, a Freud biscuit jointer, a Skil worm drive circular saw (model 77 I think?) and a Ryobi palm sander (which is a piece of $hit) and a couple of Craftsman sanders (which also suck). My cheapie router is a Porter Cable, it's "okay" it does the job.

My experience at this point amounts to a simple workbench and reading material, so excuse my ignorance in advance.

I must say, that is a sweet table saw! That baby probably cost's more by itself than my entire collection of cheapie tools! With a nice table saw like that, I assume you make furniture as well as utility woodwork?

As far as the sliding compound saw goes, I'm not sure what it could do. Couldn't you do anything it does with a table saw like that and a few jigs or sleds? I've only seen people use a miter saw to chop 2x4 or 4x4 stock. I'm guessing a 10 inch saw could chop up to 2x8 inch stock? Maybe the slide saw is easier to work with than a table saw for smaller stock? As much as I'd like a nice saw, I'm probably going to get a cheap ten inch miter. They are on sale for $69, so I don't mind if it doesn't last longer than this years projects. It will handle the 2x4 and 4x4 stock I'll be using, and I can always upgrade later if I get serious and garage sale the cheapie.

I've seen the orbital sawzall on DIY. Definitely a more aggressive tool! I believe they gauged it to cut approximately twice as fast.

[CoventryCat86]

My experience at this point amounts to a simple workbench and reading material, so excuse my ignorance in advance.

I must say, that is a sweet table saw! That baby probably cost's more by itself than my entire collection of cheapie tools! With a nice table saw like that, I assume you make furniture as well as utility woodwork?

As far as the sliding compound saw goes, I'm not sure what it could do. Couldn't you do anything it does with a table saw like that and a few jigs or sleds? I've only seen people use a miter saw to chop 2x4 or 4x4 stock. I'm guessing a 10 inch saw could chop up to 2x8 inch stock? Maybe the slide saw is easier to work with than a table saw for smaller stock? As much as I'd like a nice saw, I'm probably going to get a cheap ten inch miter. They are on sale for $69, so I don't mind if it doesn't last longer than this years projects. It will handle the 2x4 and 4x4 stock I'll be using, and I can always upgrade later if I get serious and garage sale the cheapie.

I've seen the orbital sawzall on DIY. Definitely a more aggressive tool! I believe they gauged it to cut approximately twice as fast.

Actually Kenyth, an inexpensive chop saw will probably be fine. I have one and I do admit, it still does get quite a bit of use. My brother borrowed the compound miter saw and I haven't seen it since, LOL! He used it to do his deck and some finish trim work.

Yeah, the table saw gets used for darn near everything. I suppose it's a little over the top but I tell ya, a table saw is the heart of any woodworking shop. It's the first thing you need to get. We had an old Rockwell for years, it was way underpowered and was basically a piece of junk. Now I suppose you don't have to go crazy and get a Powermatic but don't go with the cheap Taiwan crap for a table saw. The Taiwan power tools definitely have their place in any shop and I have a few myself. For instance, I have a 3hp Taiwan shaper, a Taiwan drill press, and a Taiwan band saw. A shaper is just a motor on a stand so in my opinion, there's no need to spend the $$$ on a big name shaper. For what little I use a band saw, the Taiwan band saw fits my needs. A drill press is basically nothing but a motor as well and my Taiwan drill press works just fine.

[ggiese]

Oh, another fantastic tool is an ORBITAL "sawzall" (reciprocating saw). I have an older Milwaukee regular Sawzall and I borrowed a friend's Porter Cable orbital reciprocating saw and WOW, what a difference! Here's the one you need. model 6536-21:

I'm a huge fan of Milwaukee brand power tools, it's pretty much the only brand I buy. My 3/8" drill, my 1/2" D-handle drill, my palm sander, rotary hammer drill, Sawzall are all Milwaukee brand tools. I will admit though that I have a Porter Cable power planer (door hanging kit), a Porter Cable 3/8" right angle drill, a Freud biscuit jointer, a Skil worm drive circular saw (model 77 I think?) and a Ryobi palm sander (which is a piece of $hit) and a couple of Craftsman sanders (which also suck). My cheapie router is a Porter Cable, it's "okay" it does the job.

Speaking of Milwaukee... Tossers at the Turner Ball Room on St. Patrick's Day! I'm going - are you????

[CoventryCat86]

George you bastid. I don't think I can make it......

Kenyth, as I mentioned earlier, I have a cheap-a$$ed "Chicago Electric" (Harbor Freight's cheap-a$$ed line) chop saw that pretty much does the job. I think we only paid about $40.00 for it almost 20 years ago.

If you want to go the inexpensive route, here's a good deal for ya:

http://surpluscomputers.stores.yahoo...0mitersaw.html

Here's a picture:



It's only $80.00 + shipping. It looks like the head rotates so you can do compound angels which mine doesn't do. Heck, I just may toss my Chicago Electric hunk of junk and replace it with this!

[Kenyth]

I've put up several fences, and I sink the posts in concrete and use some simple aluminum roof flashing at the very top of the concrete to create an angle finish where the post goes into the concrete so any water will drain away from the post. Its very simple to do and the flashing is inexpensive. The concrete raises about 2-3 inces above ground level so basically all the post is in contact with is the concrete.

As far as the shed goes, the footer would be the best and will also help with any critters that want to make under your shed their new home.

I might be screwing up my terminology here. By footer, does that mean a full concrete pad, or just posts in concrete or hardware embedded in concrete plugs at points where you attach the posts?

[ashauler]

I might be screwing up my terminology here. By footer, does that mean a full concrete pad, or just posts in concrete or hardware embedded in concrete plugs at points where you attach the posts?

By footer I mean a strip of concrete where the 4 x 4 laying on the ground would go, like a house foundation, just not as robust. IMO, harder to do, but better result and you don't have the wood rot to worry about.

[cinda]

my hubby's got more tools then I care to list. DO not buy craft man at homecrapo it may be cheaper but the tool is made differently. By craft man tools at sears. He has a lot of sanders, he even has a drywall sander. kitty I am trying to make you jealous.

[Kenyth]

By footer I mean a strip of concrete where the 4 x 4 laying on the ground would go, like a house foundation, just not as robust. IMO, harder to do, but better result and you don't have the wood rot to worry about.

OK, that's what I thought. That's probably one of the best ideas, but I'd like to avoid concrete work considering I'll be mixing in 5 gallon buckets. I was thinking that I could do kind of the same thing by sinking some posts at the corners with concrete and starting the frame from those using some 2x6 stock as joists. I'm not sure what would be best and easiest.

Considering I'm going to be in 3/4 time college until Jan 2010, I may have to let this project slide until next spring. The only thing that absolutely has to go up this spring is a fence, kennel area, and dog house.

[logan37]

I got an air compressor this past XMas. With the economy down, the prices on tools at Harbor Freight have been almost a givaway! I've been buying tools like crazy (to my wife's disdain)! I built a small work bench/Pegboard. It turned out fairly well! I have a few jobs to do this spring. Put up a fence, put up a shed, and put up an outdoor doghouse/kennel. I plan to build a lot of the stuff I need to work myself. My next project is making some knockdown sawhorses. I plan on modifying them to accept some 2x4 stretchers to create a knockdown work support. I figure I can just cross a couple notched 2x4's to rip or crosscut sheets if I need to. Then, I'll use OSB hinged in the middle to create the top for a knockdown work table. I also need to create a saw guide for my circular saw. I'm thinking that since I'll be cutting a lot of 4x4 and 2x4 stock for my spring projects, a 10" miter saw might be a good investment. I know that a table saw is the first recommended tool for woodworking, because it can miter as well, but I'm guessing that's more for furniture making than mitering long utility stock for framing and fence making.

Anyway, my question for the fence is, do you recommend putting the 4x4 posts in concrete? It will be meant to hold in a sizable dog. IS it 1/2 bag per post? For the shed, should I just put down some 4x4's on the ground or dig in concrete footers for that as well? Levelling the thing will probably be a pain otherwise?

Why don't you come to NY and help me renovate.