Drying out beads???

[n2advnture]

Spread them on a cookie sheet, like Toilje said, hair dryer on low until they are milky white again instead of clear.

What size humidor do you have and how many beads are you using?

~Mark

[PuffTheMagicDragon]

Used a hair dryer and worked great. I am using 1 ounce of beads in a small coolidor. It is large enough to hold all of my sticks (40 or so) and probably able to squeeze 10 more in if I needed to. I am getting ready to upgrade to a larger full size cooler and will add a pound of beads to it.

[bigtoys]

Opposite question, but I'll post here since it's current.
Just got my Heartfelt beads. Got tubes with red ends and humidi-pucks.
How should I moisten them?? They say if you soak them in water, they could fracture, but still work. How did you all do it?

[Stryprod]

Opposite question, but I'll post here since it's current.
Just got my Heartfelt beads. Got tubes with red ends and humidi-pucks.
How should I moisten them?? They say if you soak them in water, they could fracture, but still work. How did you all do it?

Several ways to do it and the amount of water depends on the amount of beads and how wet they are. I just take a teaspoon or so of distilled water, pop the end cap on the tube, and drop the water in. Some beads crack but they still work and now have more surface area. You could also take a spray bottle of distilled water and squirt some on the beads. Lastly, you can set the beads next to a big bowl of distilled water and let the beads naturally soak in the humid air but this takes a long time and really seems pointless.

edit: As far as the ratio of clear (wet) beads to milky white (dry) beads that you should have... approx 50/50 is good but if you live in a humid climate, have more white beads and if you are in the desert, have more soaked. Just remember to always have some of both to help regulate any humidity spikes or drops.

[PuffTheMagicDragon]

Now that it is summer I have increased my dry to wet bead ratio to about 70/30.

[bigtoys]

Upon opening the beads, some are clear and some are white. So it looks like they're shipped "charged" to some degree. Are they ready to go?

Same with the Humidi-pucks. Should I still moisten the sponge with some distilled water?

[cls515]

Upon opening the beads, some are clear and some are white. So it looks like they're shipped "charged" to some degree. Are they ready to go?

Same with the Humidi-pucks. Should I still moisten the sponge with some distilled water?

Not all of the beads should be clear, otherwise, they wouldn't be able to take in water from the environment. Probably 75% clear is what worked for me in the tube, but the humidor was already leveled out.

[Viper139]

Upon opening the beads, some are clear and some are white. So it looks like they're shipped "charged" to some degree. Are they ready to go?

Same with the Humidi-pucks. Should I still moisten the sponge with some distilled water?

If your goal is to add moisture to the humidor then wetting down the sponge is a good idea.

[Viper139]

Several ways to do it and the amount of water depends on the amount of beads and how wet they are. I just take a teaspoon or so of distilled water, pop the end cap on the tube, and drop the water in. Some beads crack but they still work and now have more surface area. You could also take a spray bottle of distilled water and squirt some on the beads. Lastly, you can set the beads next to a big bowl of distilled water and let the beads naturally soak in the humid air but this takes a long time and really seems pointless.

edit: As far as the ratio of clear (wet) beads to milky white (dry) beads that you should have... approx 50/50 is good but if you live in a humid climate, have more white beads and if you are in the desert, have more soaked. Just remember to always have some of both to help regulate any humidity spikes or drops.

Very good answer!